可能原因：加熱元件故障、水管堵塞或水閥問題。
Possible causes: heating element failure, water pipe blockage or water valve problems.

處理辦法：檢查加熱系統，清理水管，更換故障部件。
Solution: Check heating system, clean water pipes, replace faulty parts.

可能原因：研磨器堵塞、咖啡豆過大或潮濕、機器長時間未清潔。
Possible causes: grinder blockage, oversized or damp coffee beans, machine not cleaned for a long time.

處理辦法：拆卸清理研磨器，檢查研磨設置，更換磨豆刀片。
Solution: Disassemble and clean grinder, check grinding settings, replace bean grinding blades.

可能原因：排水管堵塞、排水泵故障、廢水箱安裝不當。
Possible causes: drain pipe blockage, drain pump failure, improper installation of waste water tank.

處理辦法：疏通排水管，檢查排水泵，重新安裝或更換廢水箱。
Solution: Unclog drain pipe, check drain pump, reinstall or replace waste water tank.

可能原因：密封圈老化、水管破裂、接頭鬆動。
Possible causes: aging sealing ring, broken water pipe, loose joint.

處理辦法：更換密封圈，修復或更換水管，緊固接頭。
Solution: Replace sealing ring, repair or replace water pipe, tighten joints.

可能原因：系統檢測到故障、溫度過高、壓力異常。
Possible causes: system detects fault, overheating, abnormal pressure.

處理辦法：檢查故障代碼，診斷具體問題，修復或更換故障部件。
Solution: Check error codes, diagnose specific problems, repair or replace faulty parts.

可能原因：電源線故障、保險絲燒斷、電路板問題。
Possible causes: power cord failure, blown fuse, circuit board problem.

處理辦法：檢查電源連接，更換保險絲，維修或更換電路板。
Solution: Check power connection, replace fuse, repair or replace circuit board.

可能原因：主板燒毀、無法識別部件、程序錯亂。
Possible causes: mainboard burned, unrecognizable components, program error.

處理辦法：檢測主板故障，更換原廠或兼容主板，重新編程。
Solution: Detect mainboard failure, replace original or compatible mainboard, reprogram.

可能原因：咖啡粉堵塞、壓力不足、萃取系統故障。
Possible causes: coffee powder blockage, insufficient pressure, extraction system failure.

處理辦法：清理萃取系統，檢查水泵壓力，更換故障部件。
Solution: Clean extraction system, check water pump pressure, replace faulty parts.

可能原因：短路、電路受潮、元件過載。
Possible causes: short circuit, damp circuit, component overload.

處理辦法：檢查電路系統，更換短路元件，確保絕緣良好。
Solution: Check circuit system, replace short-circuit components, ensure good insulation.

可能原因：初始化失敗、部件安裝不當、系統錯誤。
Possible causes: initialization failure, improper component installation, system error.

處理辦法：重新啟動，檢查部件安裝，重置系統或升級固件。
Solution: Restart, check component installation, reset system or upgrade firmware.

可能原因：研磨馬達故障、控製板問題、安全開關未啟動。
Possible causes: grinding motor failure, control board problem, safety switch not activated.

處理辦法：檢查馬達和控製板，確保安全裝置正常，更換故障部件。
Solution: Check motor and control board, ensure safety devices are normal, replace faulty parts.